What transmission will fit a Ford 302?

What transmission goes with a Ford 302?

For years, the Ford C-4 automatic was a reliable three-speed automatic transmission for many Ford products, and is fine for most 289, 302 or 351 engines that have received modest modifications.

Will a Ford 302 bolt up to a C6 transmission?

Will A Ford 302 Bolt Up To A C6 Transmission? It is possible to fit a c6 with a smallblock bellhousing pattern FE pattern, but it is not the same. It should be able to handle a 302 with a mild cam, a 4 bbl intake, and a good set of headers.

Will a 351 transmission fit a 302?

* All the parts from the 302 with the exception of the distributor and intake manifold will fit a 351w, but some of them may be undersized. * Motor mounts will be the same, exhaust will sit a little bit higher due to the extended deck height on the 351.

Will a 4R70W fit a 302?

Loc. – A 4R70W or AODE from behind any 5.0 (302) or V6 3.8L Mustang or V6 4.2L F150 will bolt up/work behind any 289/302/5.0/351W/351C/5.8L.

IT IS IMPORTANT:  Can you start a diesel engine without glow plugs?

Will a T5 transmission fit a 302?

This Deluxe T5 Transmission Conversion Kit will fit your 1969 Mustang with a 289, 302 or 351 Engine. To accomplish the conversion, the kit utilizes the late model bellhousing and cable linkage setup.

Will a C4 transmission fit a 302?

Registered. The 6cyl C4 will not work with the 302 , unless the tranny is ripped open and has some V8 pieces installed .

What engines fit a C6 transmission?

The C6 was used in trucks and cars with larger engines. Five different bell housing varieties exist for use with various Ford engine families: The Windsor pattern was used on the 300 I6, the Ford Windsor engines and the 351 Cleveland. The 460 pattern was used on the 351M and 400 and all of the Ford “385” engines.

What does a C6 transmission fit?

Also, the C6 transmission was used in high-performance vehicles as well as trucks with more significant engines such as Ford trucks, passenger cars, and Lincoln cars. The C6 was evident in the Ford F-Series between 1967 to 1996 as well as the Ford Bronco between 1978 to 1991.

What motors will bolt to a C6 transmission?

Making it the perfect transmission for Ford to pair with their 351W, 351C, 428, 429, 460, and 462 gasoline V8’s. Along with the 7.3L diesel.

Are the 302 and 351w blocks the same?

You can spot the difference pretty easily by looking at the front of the engine. On a 302 (or smaller c.i.d.) blocks, the distributor mount is almost flush with the top of the block (where the intake sits). … A 351W block is taller. So, the distributor mount is below the block surface where the intake sits.

IT IS IMPORTANT:  Is it safe to drive a car with transmission problems?

Are 302 and 351 flywheels the same?

Your 302 bellhousing & flywheel will bolt up and work fine behind a 351w.

Will 351w intake Fit 302?

5.0 trader said: This allows you to use a 289-302 on a 351w motor. This will allow you alot more options for intakes. This is a new pieces never mounted.

Will a 5.0 bolt up to a 4R70W?

As far as fitting a trans goes, the 4R70W that runs behind the 4.6 will not bolt up to a 5.0 because it has a different bellhousing bolt battern. You’ll need a trans from another 5.0 car, or a 3.8 V6 car.

What vehicles have a 4R70W transmission?

Cars that used the 4R70W transmission include:

  • Ford F-150 Series pick-up trucks, E-150 Series vans, Expeditions, Explorers, Crown Victorias, Thunderbirds, and Mustangs.
  • Lincoln Town Cars and Mark VIIIs.
  • Mercury Grand Marquis, Cougars, Mountaineers and Marauders.

Is the 4R70W a good transmission?

The 4R70W is a good transmission, but it has its pros and cons. Let’s look over some of its best qualities, and some of its faults and issues. For one, it has a much better and improved overdrive band. … That, and as with any other transmission, you still need to maintain it regularly.